View LE28F4001M_27914.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : EN*5239A
CMOS LSI
LE28F4001M, T, R-15/20
4 MEG (524288 words x 8 bits) Flash Memory
Preliminary Overview
The LE28F4001 Series ICs are 524288-word x 8-bit flash memory products that support on-board reprogramming and feature 5 V single-voltage power supply operation. CMOS peripheral circuits were adopted for high speed, low power, and ease of use. These products support a sector (256 bytes) erase function for fast data rewriting.
Package Dimensions
unit: mm 3205-SOP32
[LE28F4001M]
Features
* Fabricated in a highly reliable 2-layer polysilicon CMOS flash EEPROM process. * Read and write operation from a 5 V single-voltage power supply * Sector erase function: 256 bytes per sector * Fast access time: 150/200 ns * Low power -- Operating current (read): 25 mA (maximum) -- Standby current: 20 A (maximum) * Highly reliable read and write operations -- Sector write cycles: 104 cycles -- Data retention time: 10 years * Address and data latches * Self-timer erase and programming * Byte programming time: 35 s (maximum) * Write complete detection: Toggle bit and data polling * Hardware and software data protection * Pin assignment conforms to the JEDEC byte-wide EEPROM standard * Packages SOP 32-pin (525 mil) plastic package :LE28F4001M TSOP 40-pin (10 x 14 mm) plastic package :LE28F4001T TSOP 40-pin (10 x 14 mm) plastic package :LE28F4001R
SANYO: SOP32
unit: mm 3087A-TSOP40
[LE28F4001T, R]
SANYO: TSOP40 (TYPE-I)
These FLASH MEMORY products incorporate technology licensed Silicon Storage Technology, Inc.
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
63096HA (OT) No. 5239-1/14
LE28F4001M, T, R-15/20 Block Diagram
Pin Assignments
No. 5239-2/14
LE28F4001M, T, R-15/20 TSOP40 Standard TSOP40 Reversed
Pin Functions
Symbol A18 to A0 Address input Pin Functions Supply the memory address to these pins. The address is latched internally during a write cycle. These pins output data during a read cycle and input data during a write cycle. Data is latched internally during a write cycle. Outputs go to the high-impedance state when either OE or CE is high. The device is active when CE is low. When CE is high, the device becomes unselected and goes to the standby state. Makes the data output buffers active. OE is a low-active input. Makes the write operation active. WE is a low-active input. Apply 5 V (10%) to this pin.
DQ7 to DQ0
Data input and output
CE OE WE VCC VSS N.C.
Chip enable Output enable Write enable Power supply Ground No connection
These pins must be left open.
Function Logic
Mode Read Write Standby or write inhibit Write inhibit CE VIL VIL VIH X X OE VIL VIH X VIL X WE VIH VIL X X VIH AIN AIN X X X A18 to A10 = VIL, A8 to A1 = VIL, A9 = 12 V, A0 = VIL A18 to A10 = VIL, A8 to A1 = VIL A9 = 12 V, A0 = VIH A18 to A0 DOUT DIN High-Z High-Z/DOUT High-Z/DOUT Manufacturer code (BF) DQ7 to DQ0
Product identification
VIL
VIL
VIH
Device code (04)
Command Settings
Command Sector erase Byte program Reset Read ID Software data unprotect Software data protect Request cycle 2 2 1 3 7 7 Setup command cycle Operation Write Write Write Write See Figure 9. See Figure 10. Address X X X X Data 20H 10H FFH 90H Read (7) (7) Execute command cycle Operation Write Write Address SA PA Data D0H PD N N Y Y SDP
No. 5239-3/14
LE28F4001M, T, R-15/20 Notes on Command Settings Type definitions: X = Don't care Address definitions: SA = Sector Address = A18 to A8; sector size = 256 bytes; A7 to A0 = X for this command. Address definitions: PA = Program Address = A18 to A0. Data definition: PD = Program Data, H = number in hex. SDP = Software Data Protect mode using 7-read-cycle sequence. Y = the operation can be executed with software data protect enabled. N = the operation cannot be executed with software data protect enabled. 6. Refer to figures 9 and 10 for the 7-read-cycle sequence software data protection. 7. Address 0000H retrieves the manufacturer code of BF (hex), address 0001H retrieves the device code of 04 (hex). Product Overview The LE28F4001 Series products are EEPROMs that support sector erase and byte programming functions and that feature a 512K x 8 organization. These products support both erase and programming from a 5-V single-voltage power supply, conform to the JEDEC standards for byte-wide memory pin assignments, and are pin compatible with industry standard EPROMs, flash EPROMs, and EEPROMs. The LE28F4001 Series products, provide a 35 s maximum byte programming time and a 4 ms sector erase time. Programming and erase operations can both be optimized by using the toggle bit and Data polling functions that indicate the completion of the write cycle. To protect data against unintentional writes, these products provide both hardware and software data protection schemes. The LE28F4001 Series products, guarantee 104 sector write cycles. The data retention time is ten years or longer. The LE28F4001 Series functional block diagram and the 40-pin TSOP and 32-pin SOP package pin assignments are shown on page 2, and the pin functions and command settings are listed on page 3. Device Operation Commands are used to execute the device's memory functions. Commands are written to the command register with standard microprocessor write timing. Commands are written by setting WE low while CE is held low. The address is latched on the falling edge of either CE or WE, whichever occurs later. Data is latched on the rising edge of either CE or WE, whichever occurs first. However, the address is latched on the rising edge of either OE or CE, whichever occurs first during the software write protect sequence. Command Definition The "Command Settings" section provided an overview and list of the LE28F4001 commands. This section describes the functions provided by those commands in detail. Before executing the LE28F4001 Series byte programming or erase functions, the application system must execute the software data unprotect sequence. 1. 2. 3. 4. 5.
No. 5239-4/14
LE28F4001M, T, R-15/20 1. Sector erase operation The sector erase operation consists of a setup command and an execute command. The setup commands sets the device to a state where all the bytes in the sector can be erased electrically. A single sector has 256 bytes. Since almost all applications use erase operations that are not whole-chip erase operations but rather are single sector erase operations, this sector erase function significantly increases the flexibility and ease of use of the LE28F4001 Series. The setup command is executed by writing 20H to the command register. An execute command (D0H) must be written to the command register to execute the sector erase operation. The sector erase operation starts on the rising edge of the WE pulse and is automatically completed under internal timing control. Figure 6 shows the timing waveforms for this operation. This two stage sequence in which a setup command and a following execute command are required guarantees that the memory at the sector specified by the address data will not be erased accidentally. 2. Sector erase flowchart The quick and reliable erasure of up to 256 bytes of memory can be achieved by following the sector erase flowchart shown in Figure 1. The whole operation consists of executing two commands. A sector erase operation completes in a maximum of 4 ms. Although the erase operation can be completed by executing a reset operation, the sector may not be completely erased if that reset is executed before the 4 ms time out period elapses. The erase command can be re-executed as many times as required before the erase completes. Excessive erasure cannot cause problems with the LE28F4001 Series products. 3. Byte programming operation The byte programming operation is started by writing a setup command (10H) to the command register. Once the setup command is executed, the execute command is started by the next WE pulse transition. Figure 7 shows the timing waveforms for this operation. The address and the data are latched internally on the falling edge and rising edge of the WE pulse, respectively. The WE rising edge also corresponds to the start of the programming operation. The programming operation is automatically completed under internal timing control. Figures 2 and 7 show the programming characteristics and waveforms. As mentioned previously, this two stage sequence in which a setup command and a following execute operation are required guarantees that the memory cells will not be programmed accidentally. 4. Byte programming flowchart Figure 2 shows the device data programming operation. This is effected by following the byte programming flowchart. The byte programming command sets up the byte to be written. The address is latched on the falling edge of WE or CE, whichever is later. The data bus is latched on the rising edge of WE or CE, whichever is earlier, and the programming operation starts at that point. The completion of the write operation can be detected using either the toggle bit or by polling a Data pin. 5. Reset operation The reset command is a procedure for safely terminating an erase or programming command sequence. Writing FFH to the command register after issuing an erase or programming setup command will safely cancel that operation. The contents of memory will not be changed. The device goes to read mode after executing a reset command. The reset command cannot activate the software data protect function. Figure 8 shows the timing waveforms. 6. Read operation A read operation is performed by setting CE and OE, and then WE, to read mode. Figure 3 shows the read mode timing waveforms, and the read mode conditions are shown as "functional logic". A read cycle from the host searches for the memory array data. The device remains in the read state until another command is written to the command register. As a default, the device will be in read mode in the write protect state from the time power is first applied until a command is written to the command register. The unprotect sequence must be executed to perform a write operation (erase or programming). The read operation is controlled by CE and OE, and both must be set to the logic low level to activate the read function. When CE is at the logic high level, the chip is in the unselected state and only draws the standby current. OE controls the output pins. The device output pins will be in the high-impedance state if either CE or OE is at the logic high level.
No. 5239-5/14
LE28F4001M, T, R-15/20 7. Read ID operation The read ID (identifier) operation consists of a single command, 90H. A read operation from address 0000H will then return the manufacturer code (BFH) and a read operation from address 0001H will return the device code (04H). This operation is terminated by writing any other valid command to the command register. Protecting Data from Unintentional Writes To protect the accumulated stored data that the user intends to be nonvolatile, the LE28F4001 Series products provide both hardware and software functions to prevent unintentional writes when power is applied or cut off. 1. Hardware data protection The LE28F4001 Series products incorporate a hardware data function that prevents unintentional writes. * Write inhibit mode: Write operations are disabled if either OE is at the low logic level, CE is at the high logic level, or WE is at the high logic level. * Noise and glitch protection: WE pulses shorter than 15 ns will not execute a write operation. * The LE28F4001 Series products were designed to hold unintentional writes to a minimum by setting the device to read mode as the default when power is first applied. 2. Software data protection As mentioned earlier, the LE28F4001 Series is designed to provide even more protection from unintentional writes in software. To avoid unintentional erasure or programming of sector or device cells, when the application system attempts to execute a sector erase or programming operation it must execute that operation as a two-stage sequence consisting of first of a setup command and then an execute command. As a default, the LE28F4001 Series products go to the write protected state after power is applied. The device goes to the unprotected state after reads to seven specific addresses are executed consecutively. Those addresses are 1823H, 1820H, 1822H, 0418H, 041BH, 0419H, and 041AH. The address is latched on the rise of either OE or CE, whichever is earlier. Similarly, the device can be set to the write protect state by reading from the following 7 addresses consecutively: 1823H, 1820H, 1822H, 0418H, 041BH, 0419H, and 040AH. Figures 9 and 10 show the software data protection waveforms for this 7-read-cycle sequence. The I/O pins can go to any state (high, low, or high impedance). Detection of Write Operation Completion To acquire the maximum performance from the device, the application must detect the completion of the programming cycle. The completion of the programming cycle can be detected by either Data polling or the toggle bit. This section describes these two detection mechanisms. Actually, the completion of a nonvolatile memory write operation is asynchronous with respect to the application system. Therefore, it is possible that readout of either Data polling or toggle bit data could occur at the same time as the completion of the write cycle. If this happens the application system might get an incorrect result. That is, valid data could appear to contradict either DQ7 or DQ6. To prevent artificial rejections, if an incorrect result occurs, the software routine must include a loop to read the accessed location another 2 times. If both these readout cycles acquire valid data the device will have completed the write cycle. All other reject states are correct. 1. Data polling (DQ7) The LE28F4001 Series products provide a Data polling function that detects the completion of the programming cycle. During the program cycle, DQ7 reads out data that is the negation of the most recently loaded data. When the programming cycle has completed, DQ7, along with DQ0 to DQ6, reads out the last loaded data. Figure 11 shows the timing chart for this operation. For Data polling to function correctly, data must be erased before programming. 2. Toggle bit (DQ6) The DQ6 toggle bit is another technique for detecting the end of the erase or programming cycle. During an erase or programming operation the value of the DQ6 output alternates between 0 and 1, that is, the DQ6 output toggles between 0 and 1. When the erase or programming cycle completes, the toggling stops and the device goes to a normal read cycle. The toggle bit can be continuously monitored during an erase or programming cycle. Figure 12 shows the timing chart for toggle bit operation. 3. Continuous read One more technique for detecting the end of an erase or programming cycle is to read the same address twice in a row. If the same data is read twice in a row the erase or programming cycle has completed.
No. 5239-6/14
LE28F4001M, T, R-15/20 Product Identifier Product identifier read is a mode provided so that applications can confirm that the device was manufactured by SANYO Electric Co., Ltd. This mode can be accessed by both hardware and software operations. A ROM writer is normally used with this hardware operation to recognize the correct algorithm for the SANYO LE28F4001 Series. We recommend that user use the software operation for recognizing this device. The "Functional Logic" section describes the hardware operation in detail. The manufacturer and device code are accessed in the same manner. Decoupling Capacitors Ceramic capacitors (0.1 F) must be added between VCC and VSS for each device to assure stabile flash memory operation. Absolute Maximum Ratings at Ta = 25C
Parameter Supply voltage Input pin voltage DQ pin voltage A9 pin voltage Power dissipation Operating temperature Storage temperature Note: 1. 2. 3. 4. Symbol VCC VIN VI/O VA9 Pd max Topr Tstg Ratings -0.5 to +6.0 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 -0.5 to +14.0 600 0 to +70 -65 to +150 Unit V V V V mW C C Note 1 1, 2 1, 2 1, 3 1, 4 1 1
Stresses greater than the above listed maximum values may result in damage to the device. -1.0 to VCC + 1.0 V for pulse widths less than 20 ns. -1.0 to VCC + 14.0 V for pulse widths less than 20 ns. Ta = 25 C
DC Recommended Operating Ranges at Ta = 0 to +70C, VCC = 5 V 10%
Parameter Supply voltage Input low-level voltage Input high-level voltage Symbol VCC VIL VIH 2.0 min 4.5 typ 5.0 max 5.5 0.8 Unit V V V
DC Electrical Characteristics at Ta = 0 to +70C, VCC = 5 V 10%
Parameter Current drain during read Current drain during write TTL standby current CMOS standby current Input leakage current Output leakage current Output low-level voltage Output high-level voltage Symbol ICCR ICCW ISB1 ISB2 ILI ILO VOL VOH Conditions CE = OE = VIL, WE = VIH, all DQ pins open, Address inputs = VIH or VIL, operating frequency = 1/tRC (minimum), VCC = VCC max CE = WE = VIL, OE = VIH, VCC = VCC max CE = VIH, VCC = VCC max CE = VCC - 0.3 V, VCC = VCC max VIN = VSS to VCC, VCC = VCC max VIN = VSS to VCC, VCC = VCC max IOL = 2.1 mA, VCC = VCC min IOH = -400 A, VCC = VCC min 2.4 min typ max 25 40 3 20 10 10 0.4 Unit mA mA mA A A A V V
Input/Output Capacitances at Ta = 25C, VCC = 5 V 10%, f = 1 MHz
Parameter I/O capacitance Input capacitance Symbol CDQ CIN VDQ = 0 V VIN = 0 V Conditions max 12 6 Unit pF pF
Power on Timing
Parameter Time from power on until first read operation Time from power on until first write operation Symbol tPU-READ tPU-WRITE max 10 10 Unit ms ms
No. 5239-7/14
LE28F4001M, T, R-15/20 AC Electrical Characteristics at Ta = 0 to +70C, VCC = 5 V 10% AC Test Conditions Input rise and fall times: .................10 ns (max.) Output load: ....................................1 TTL gate + 30 pF Read Cycle
LE28F4001M, T, R Parameter Symbol min Read cycle time CE access time Address access time OE access time CE to output low impedance time OE to output low impedance time CE to output high impedance time OE to output high impedance time Address to output valid time tRC tCE tAA tOE tCLZ tOLZ tCHZ tOHZ tOH 0 0 0 40 40 0 150 150 150 70 0 0 50 50 -15 max min 200 200 200 75 -20 max ns ns ns ns ns ns ns ns ns Unit
Erase/Programming Cycle
LE28F4001M, T, R Parameter Symbol min Sector erase cycle time Byte programming cycle time Address setup time Address hold time CE and WE setup time CE and WE hold time OE setup time OE hold time CE pulse width WE pulse width WE standby pulse width CE standby pulse width Data setup time Data hold time Reset recovery time Protect mode CE pulse width Protect mode CE hold time Protect mode address setup time Protect mode address hold time tSE tBP tAS tAH tCS tCH tOES tOEH tCP tWP tWPH tCPH tDS tDH tRST tPCP tPCH tPAS tPAH 100 150 20 100 0 50 0 0 10 10 80 80 50 50 50 10 4 100 150 30 100 -15 max 4 35 0 50 0 0 10 10 100 100 50 50 50 10 4 min -20 max 4 35 ns s ns ns ns ns ns ns ns ns ns ns ns ns s ns ns ns ns Unit
Note: All signals must hold valid logic levels during the setup and hold times.
No. 5239-8/14
LE28F4001M, T, R-15/20
Figure 1 Sector Erase Flowchart
No. 5239-9/14
LE28F4001M, T, R-15/20
Figure 2 Byte Programming Flowchart
No. 5239-10/14
LE28F4001M, T, R-15/20
Figure 3 Read Cycle
Figure 4 WE Control Write Cycle
Figure 5 CE Control Write Cycle
No. 5239-11/14
LE28F4001M, T, R-15/20
Figure 6 Sector Erase
Figure 7 Byte Programming
Figure 8 Reset
No. 5239-12/14
LE28F4001M, T, R-15/20
Note: 1. Addresses are latched internally on the rising edge of: * OE if CE is kept low all time. * CE if OE is kept low all time. * The first pin to go high if both are togglet. 2. Above address values are in hex.
Figure 9 Software Data Unprotect Sequence
Note: 1. Addresses are latched internally on the rising edge of: * OE if CE is kept low all time. * CE if OE is kept low all time. * The first pin to go high if both are togglet. 2. Above address values are in hex.
Figure 10 Software Data Protect Sequence
Figure 11 Data polling(DQ7)
No. 5239-13/14
LE28F4001M, T, R-15/20
Note: The timings stipulated here differ with the mode used. Either tSE or tBP applies.
Figure 12 Toggle Bit (DQ6)
Note: AC test inputs are driven at VOH (2.4 VTTL) for a logic 1 and VOL (0.4 VTTL) for a logic 0. The I/O measurement reference points are VIH (2.0 VTTL) and VIL (0.8 VTTL). The input rise and fall times (10% 90%) must be 10 ns or shorter.
Figure 13 AC I/O Reference Waveform
s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. s Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. s Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of February, 1997. Specifications and information herein are subject to change without notice. No. 5239-14/14

▲Up To Search▲

Price & Availability of LE28F4001M

	To Download LE28F4001M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .